York Affinity Gas Furnaces

These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

Special Benefits

• Compact 33" Height and Standard Cabinet Widths
• Multi-Position Design With Minimal Conversion Requirements
• Airflow Leakage Rate of Less Than 1% of Total Airflow @ 1" ESP
• ECM Variable-Speed Motor with Large, Quiet Blower
• Fully-Supported, Slide-Out Blower Assembly for Easy Service Access
• High-Level Self-Diagnostic Controls With Fault Codes
• Sharp Edges Have Been Eliminated By Folding and Flattening the Sheet Metal
• Fully-Gasketed, Independent Access Doors With View Ports and Attractive Retail Appearance
• Patent-Pending Condensate Management System Eliminates the Need for External Condensate Traps

These Category IV, highly efficient, compact, condensing type furnaces are designed for residential and commercial installations in a basement, closet, alcove, recreation room or garage where the ambient temperature is above 32 deg F, or higher. They may be either side wall or thru-roof vented using approved plastic type combustion air and vent piping. All units are factory assembled, wired and tested to assure dependable and economical installation and operation.

Special Benefits

• Compact, easy to install, ideal height 40" cabinet.
• Hi-tech tubular aluminized steel primary heat exchanger.
• Secondary (condensing) heat exchanger of 29-4C high grade stainless steel.
• Two stage heating operation includes:
  • Two stage gas valve
  • Two stage inducer operation
  • Variable speed ECM blower operation
• 100% shut off main gas valve for extra safety.
• Built-in, high level self diagnostics with fault code display.
• Provides increased comfort level & very quiet unit operation.
• Adjustable delay timer allows two stage operation with single stage thermostat.
• Blower-off delay for cooling SEER improvement.
• Easy to connect power/control wiring.
• Low unit amp requirement for easy replacement application.
• Integrated control module for reliable, economical operation.
• May be installed as either two-pipe (sealed combustion) or single pipe vent (using indoor combustion).
• Top intake & vent connection allows installation in narrow locations.
• Electronic Hot Surface Ignition saves fuel cost with increased dependability and reliability.
• Induced combustion system with inshot main burners for quiet, efficient operation.
• No special vent termination kit required.
• 24v, 40VA control transformer and blower relay supplied for add-on cooling.
• Timed on, adjustable off blower capability for maximum comfort.
• Solid removable bottom panel allows easy application.
• Easy access from front of unit for cleaning, maintenance or service.
• Protection from intake, exhaust or condensate blockage.
• Insulated blower compartment for quiet operation.
• ClimatraK comfort system allows dealers to customize setting based on regional location.

These compact units employ induced combustion, reliable hot surface ignition and high heat transfer aluminized tubular heat exchangers. The units are factory shipped for installation in upflow or horizontal applications and may be converted for downflow applications.

These furnaces are designed for residential installation in a basement, closet, alcove, attic, recreation room or garage and are also ideal for commercial applications. All units are factory assembled, wired and tested to assure safe dependable and economical installation and operation.

These units are Category I listed and may be common vented with another gas appliance as allowed by the National Fuel Gas Code.

Special Benefits

• Compact 33??? Height and Standard Cabinet Widths
• Multi-Position Design With Minimal Conversion Requirements
• Airflow Leakage Rate of Less Than 1% of Total Airflow @ 1??? ESP
• ECM Variable-Speed Motor with Large, Quiet Blower
• Fully-Supported, Slide-Out Blower Assembly for Easy Service Access
• Tubular Aluminized Steel Primary Heat Exchanger
• High-Level Self-Diagnostic Controls With Fault Codes
• Sharp Edges Have Been Eliminated By Folding and Flattening the Sheet Metal
• Fully-Gasketed, Independent Access Doors With View Ports and Attractive Retail Appearance
• All Models Are Propane Convertible
• Lo-Nox Models Meet Specific Code Requirements